Renegade Public Forums
C&C: Renegade --> Dying since 2003™, resurrected in 2024!
Home » Technical Support » Other » RJ45 connectors
RJ45 connectors [message #191990] Mon, 06 March 2006 05:09 Go to next message
-MP-puddle is currently offline  -MP-puddle
Messages: 5
Registered: October 2005
Location: Glasgow, Scotland, UK.
Karma: 0
Recruit
I have 3 PCs in the house and want to network them through a router.

Currently I am able to use a LAN. cable only between 2 PCs.

I was informed that to network, using a router and hard wiring that the RJ45s would need to be "straight" as opposed to "crossed".

The router will not setup and neither of the cables even light up at the rear of the PC when connected. I cant even use them as LAN. cables.

All connections are as per the diagram for RJ45 straight. All wires are properly crimped.

What has gone wrong? Blush
Re: RJ45 connectors [message #192164 is a reply to message #191990] Tue, 07 March 2006 23:36 Go to previous messageGo to next message
mision08 is currently offline  mision08
Messages: 525
Registered: May 2005
Location: Cattle Drive, Dallas to F...
Karma: 0
Colonel
What Operating systems are you using? What is the name, and model of the router? What is the configuration, cable ISP? Can you reach the router Ip address? http://192.168.1.1/

Re: RJ45 connectors [message #192169 is a reply to message #191990] Wed, 08 March 2006 02:27 Go to previous messageGo to next message
light is currently offline  light
Messages: 988
Registered: January 2005
Karma: 0
Colonel
Most modern hubs/routers will automatically detect crossed/straight cables and behave accordingly.

However, best way is (as you have done) to use straight cables for each PC on the network. (I have a crossed going from my modem to my hub, the rest are straight).

If the lights aren't showing I can only presume that the electronic connection is not being established, so i'd blame the cable.

Do you have any pre-made cables you can try?


http://www.azupload.com/displayImage.php/setid2745.png
Re: RJ45 connectors [message #192225 is a reply to message #192169] Wed, 08 March 2006 18:25 Go to previous message
mision08 is currently offline  mision08
Messages: 525
Registered: May 2005
Location: Cattle Drive, Dallas to F...
Karma: 0
Colonel
light wrote on Wed, 08 March 2006 03:27

Most modern hubs/routers will automatically detect crossed/straight cables and behave accordingly.

However, best way is (as you have done) to use straight cables for each PC on the network. (I have a crossed going from my modem to my hub, the rest are straight).

If the lights aren't showing I can only presume that the electronic connection is not being established, so i'd blame the cable.

Do you have any pre-made cables you can try?


I have to agree.
You need to establish a local connection between your computer and your modem. Then, a connection with your ISP. After that, incorporate the router, and establish a local connection to it

http://192.168.1.1/

At the password prompt, leave username blank, password = admin. Once all these things are done, you should only need to connect the other PC to the router and configure windows and its firewall. Damn, you should call your ISP, they are in a better position to help. Atleast they can tell you if they see your modem or not.
Also, a handy thing to know is at the run prompt type, cmd at command prompt type,
ipconfig /all
ipconfig /help

I've dazzled many a disgruntled user with a simple
ipconfig /release
ipconfig /renew


[Updated on: Wed, 08 March 2006 21:00]

Report message to a moderator

Previous Topic: Gamespy nickname login problem: "bad installation error"
Next Topic: GFX Question.
Goto Forum:
  


Current Time: Thu Nov 21 17:42:54 MST 2024

Total time taken to generate the page: 0.01411 seconds