Command and Conquer: Renegade Official Forums: Mod Forum

Home » Renegade Discussions » Mod Forum » Buildings Reconized by renegade

Show: Today's Messages :: Polls :: Message Navigator

Buildings Reconized by renegade [message #68487]

Tue, 24 February 2004 08:52

Oblivion165
Messages: 3468
Registered: June 2003
Location: Hendersonville, North Car...

Karma: 0

General (3 Stars)

when i make any kind of building, hen i put it in renegade, how do you get it to show the name of it?

like when you look at GDI barracks, it says Barracks on it.

anyhelp?

WOL: Ob165ion Skype: Oblivion165 Yahoo Instant Messenger: CaptainJohn165

Report message to a moderator

Buildings Reconized by renegade [message #68712]

Tue, 24 February 2004 23:04

IRON FART
Messages: 1989
Registered: September 2003
Location: LOS ANGELES

Karma: 0

General (1 Star)

Sink lower the building controller of the BArracks for example into the structure itself in Level Editor. http://www.renhelp.co.uk find a map tut and it will explain better.

Report message to a moderator

Buildings Reconized by renegade [message #68714]

Tue, 24 February 2004 23:20

Titan1x77
Messages: 1086
Registered: February 2003

Karma: 0

General (1 Star)

That involves Strings.tdb...Talk to ACK

"But if the gameplay sucks, the looks don't matter at all." - Sir Phoenixx

Report message to a moderator

Buildings Reconized by renegade [message #68717]

Tue, 24 February 2004 23:47

Aircraftkiller
Messages: 8213
Registered: February 2003

Karma: 1

General (5 Stars)

He's asking how the structures are recognized, as in "point at the building and it has a targeting bracket."

That involves placing the respective building controller in the preset list for the structure you want to use. It has to be on, or near, the structure in question for Renegade to realize what it is and apply damages\animations accordingly.

Report message to a moderator

Buildings Reconized by renegade [message #68768]

Wed, 25 February 2004 11:52

Blazer
Messages: 3322
Registered: February 2003
Location: Phoenix, AZ

Karma: 0

General (3 Stars)
Administrator/General

IRON-FART

Sink lower the building controller of the BArracks for example into the structure itself in Level Editor.

Hmm didn't Dante just point out in his tutorial that building controllers don't actually have to be stuck into the mesh of the building?

Report message to a moderator

Buildings Reconized by renegade [message #68772]

Wed, 25 February 2004 12:05

General Havoc
Messages: 1564
Registered: February 2003
Location: Birmingham, England, Unit...

Karma: 0

General (1 Star)

To cut a very long story short and avaoid all of my things I would say about doing this, you need to read some tutorial, but it basically invloves naming the meshes for the interior and ones for the exterior using a prefix. For example "MNPWG^Roof" where NMPWR is the prefix and "^" is the type indicator, for interior meshes you use "#" such as "MNPWR#Ceiling" with that done, you export to Leveledit as terrain and then modify a building controller to use the prefix you chose.

Note: You cannot use the same prefix for both teams or you will have a "clone" of your building in the game and will cause problems. Westwood used "MN" for Nod and "MG" for GDI, followed by a short name, such as "PWR" for power plant, do not exceed more than 17 characters in naming the whole mesh, the prefix should remain short.

Visit my website at http://renhelp.laeubi-soft.de powered by laeubi.de
"SHUT UP AND MOD" - Dante
"ACK is the Simon Cowell of modding" - Ultron10
Scripts.dll Debugger, Map Scripter and Tutorial writer

Computer Science Bsc
Aston University in Birmingham, UK

Report message to a moderator

Previous Topic:	Renegade Alert Iron Curtain
Next Topic:	ChronoShift inspired by AircraftKiller

Goto Forum:

-=] Back to Top [=-

[ Syndicate this forum (XML) ] [

] [

]

Current Time: Fri Dec 20 19:13:23 MST 2024

Total time taken to generate the page: 0.00805 seconds