Renegade Public Forums
C&C: Renegade --> Dying since 2003™, resurrected in 2024!
Home » Renegade Discussions » Mod Forum » Need help water texture
Need help water texture [message #441784] Wed, 22 December 2010 13:41 Go to next message
my486CPU is currently offline  my486CPU
Messages: 56
Registered: June 2010
Karma: 0
Recruit
I have been looking for a tut (with know luck) on making water transparent like on fields mix. Does anyone know were I might find a good tut? Or maybe what the vertex and shader settings would be? I'm using gmax and for a texture I'm using l05_creek.tga(found in always).

I'm hoping someone could help a noob out.
Thanks.

Report message to a moderator

Re: Need help water texture [message #441785 is a reply to message #441784] Wed, 22 December 2010 15:53 Go to previous messageGo to next message
wubwub is currently offline  wubwub
Messages: 142
Registered: May 2009
Location: Ontario
Karma: 0
Recruit
Make the vertex shader Screen.

When renegade goes Wub, it never goes back

(or at least until I re-install renegade anyways)

http://i266.photobucket.com/albums/ii272/ZaydenX/Walrus-Sig.jpg

Report message to a moderator

Re: Need help water texture [message #442259 is a reply to message #441785] Thu, 06 January 2011 17:10 Go to previous messageGo to next message
Jerad2142 is currently offline  Jerad2142
Messages: 3826
Registered: July 2006
Location: USA
Karma: 6
General (3 Stars)
In addition make sure to make the lighting passes black except for the emissive, or else you'll start pulling your hair out once you generate the levels lighting and it turns to bright white (Note: there are other ways around this but I'd have to look it up in my notes, which are currently not accessible due to an attempt to clone my hard drive).


Visit Jerad's deer sweat shop

Report message to a moderator

Re: Need help water texture [message #442555 is a reply to message #442259] Wed, 12 January 2011 18:05 Go to previous messageGo to next message
my486CPU is currently offline  my486CPU
Messages: 56
Registered: June 2010
Karma: 0
Recruit
Jerad Gray wrote on Thu, 06 January 2011 19:10

In addition make sure to make the lighting passes black except for the emissive, or else you'll start pulling your hair out once you generate the levels lighting and it turns to bright white (Note: there are other ways around this but I'd have to look it up in my notes, which are currently not accessible due to an attempt to clone my hard drive).



So that's the trick. Once again you've come through for me Mr. Gray. Now I just need to find some glue to put my hair back on Big Grin

Report message to a moderator

Re: Need help water texture [message #442605 is a reply to message #442555] Thu, 13 January 2011 13:08 Go to previous message
Jerad2142 is currently offline  Jerad2142
Messages: 3826
Registered: July 2006
Location: USA
Karma: 6
General (3 Stars)
my486CPU wrote on Wed, 12 January 2011 18:05

Jerad Gray wrote on Thu, 06 January 2011 19:10

In addition make sure to make the lighting passes black except for the emissive, or else you'll start pulling your hair out once you generate the levels lighting and it turns to bright white (Note: there are other ways around this but I'd have to look it up in my notes, which are currently not accessible due to an attempt to clone my hard drive).



So that's the trick. Once again you've come through for me Mr. Gray. Now I just need to find some glue to put my hair back on Big Grin

No problem, although you'll have to choose out your choice glue yourself, all I know is renegade. XP


Visit Jerad's deer sweat shop

Report message to a moderator

Previous Topic: Walls Remake
Next Topic: Ion cannon beam w3d filename
Goto Forum:
  

[ Syndicate this forum (XML) ] [ RSS ] [ PDF ]

Current Time: Fri Nov 07 01:48:26 MST 2025

Total time taken to generate the page: 0.00692 seconds
.:: Contact :: Home ::.

Powered by: FUDforum 420.69.
Copyright ©2001-2023 FUDforum Bulletin Board Software