Renegade Public Forums
C&C: Renegade --> Dying since 2003™, resurrected in 2024!
Home » Renegade Discussions » Mod Forum » Export Problems
Export Problems [message #139032] Fri, 18 February 2005 05:06 Go to next message
danpaul88 is currently offline  danpaul88
Messages: 5795
Registered: June 2004
Location: England
Karma: 0
General (5 Stars)
When I export models from RenX and open them in w3d viewer or level edit they suddenly have holes in them, polys that seem to have turned invisable. Why is this? Confused

I tried deleting the problem polys and re-making them but the same thing happened.

http://steamsignature.com/card/1/76561197975867233.png

Report message to a moderator

Export Problems [message #139359] Sat, 19 February 2005 11:42 Go to previous messageGo to next message
danpaul88 is currently offline  danpaul88
Messages: 5795
Registered: June 2004
Location: England
Karma: 0
General (5 Stars)
any suggestions?

http://steamsignature.com/card/1/76561197975867233.png

Report message to a moderator

Export Problems [message #139365] Sat, 19 February 2005 12:47 Go to previous messageGo to next message
Oblivion165 is currently offline  Oblivion165
Messages: 3468
Registered: June 2003
Location: Hendersonville, North Car...
Karma: 0
General (3 Stars)
easy to fix, simply select all your meshes then

Hammer Tab ~ w3d Tools ~ Assign node names

Set it to something short. The names cannot be longer than 15 characters.

WOL: Ob165ion Skype: Oblivion165 Yahoo Instant Messenger: CaptainJohn165

Report message to a moderator

Export Problems [message #139457] Sun, 20 February 2005 01:35 Go to previous messageGo to next message
danpaul88 is currently offline  danpaul88
Messages: 5795
Registered: June 2004
Location: England
Karma: 0
General (5 Stars)
its not whole meshes that are missing, just a few faces from them. See below...

in renx
http://www.members.lycos.co.uk/dp88/images/testimg0.jpg

in w3d viewer (same in leveledit and renegade). Notice the 'hole' in the mesh...
http://www.members.lycos.co.uk/dp88/images/testimg1.jpg

http://steamsignature.com/card/1/76561197975867233.png

Report message to a moderator

Export Problems [message #139469] Sun, 20 February 2005 05:12 Go to previous messageGo to next message
Deactivated is currently offline  Deactivated
Messages: 1503
Registered: February 2003
Karma: 0
General (1 Star)
Detach the missing polys it and attach.

Report message to a moderator

Export Problems [message #139726] Mon, 21 February 2005 12:34 Go to previous message
danpaul88 is currently offline  danpaul88
Messages: 5795
Registered: June 2004
Location: England
Karma: 0
General (5 Stars)
thanks, it worked Smile

http://steamsignature.com/card/1/76561197975867233.png

Report message to a moderator

Previous Topic: Make Rocks
Next Topic: Nevermind, Solved
Goto Forum:
  

[ Syndicate this forum (XML) ] [ RSS ] [ PDF ]

Current Time: Wed May 06 02:31:04 MST 2026

Total time taken to generate the page: 0.00694 seconds
.:: Contact :: Home ::.

Powered by: FUDforum 420.69.
Copyright ©2001-2023 FUDforum Bulletin Board Software